Sensors and Modules on Sale
View All2 Channels Relay Module – 5Volts
2 Channels Relay Module – 5Volts is two channels relay module small in size that works on 5V DC power supply. This relay module is able to control two equipments from 220V to 250V power loads that can be controlled directly from Arduino, Raspberry Pi, and other microcontrollers or other low voltage circuits.
Female Headers – 2.54mm Pitch – 40 Pins
Female Headers – 2.54mm Pitch – 40 Pins is a female header use to mount directly on your pcb. It has a 2.54mm pitch that can be directly use in General PCB. It can also be connected with your arduino boards like Arduino UNO and Arduino Mega and Arduino Nano. One side of the pins are male pins and the other side is female connector. You can cut this header short as per your requirement.
DC Power Jack Female Connector Screw
DC Power Jack Female Connector Screw are ideal to use in distinct electronic projects where you require to connect disconnect the DC power supply to your circuit frequently. DC Power Jack Female Connector can be fixed with a screw to your cabinet or board.
NODEMCU ESP8266 Wifi Development Board
NODEMCU ESP8266 Wifi Development Board is an IoT Module primarily based on ESP8266 wifi Module. NODEMCU ESP8266 Wifi Development Board employs Lua Scripting language and is an open source IoT (Internet of Things) platform has CH340g USB to TTL IC.
Vibration Sensor Module
Vibration Sensor Module SW-420 is primarily based on the vibration sensor and Comparator LM393 to identify if there is any vibration that beyond the threshold. The sensitivity can be adjusted using an inbuilt potentiometer. When there is no vibration then the output is LOW and the signal indicates LED light.
LM2596 DC-DC Buck Converter Module
LM2596 DC-DC Buck Converter Module
LM2596 DC-DC Buck Converter Module is an adjustable Step Down power supply. The Input DC Volt 3.2v – 40v converts into Output DC Volt 1.2v – 35v.
220V AC Mains Wire Cable – 2 Pins
220V AC Mains Wire Cable – 2 Pins
220V AC Mains Wire Cable – 2 Pins is a High Quality Mains Cord/Wire. The wire is a 2.5 Yards (2.3 Meters Approx) long wire.
Crocodile Clip Flexible Wires Multicolor – 5 Pcs
Crocodile Clip Flexible Wires Multicolor – 5 Pcs
Crocodile Clip Flexible Wires Multicolor – 5 Pcs are best to use in various electronic projects where you need to connect disconnect the circuit frequently. It is suitable to use to connect with Arduino Boards, Sensors and Modules. The wire is flexible about 19 inches long. Both sides of the wire has Crocodile/ Alligator type connectors covered with soft sleeve that work as an insulation.
UNO R3
UNO R3 Board has 32 Kb of Flash Memory and consists of 14 Digital Input / Output pins, 6 Analog Input pins, an Onboard 16 MHz Ceramic Resonator, Port for USB connection, Onboard DC Power Jack, An ICSP header and a micro-controller Reset button.
USB A To USB B Cable for Arduino – Blue Color
USB A To USB B Cable for Arduino – Blue Color
USB A To USB B Cable for Arduino – Blue Color is a High Quality USB Cable to use with Arduino Boards like Arduino UNO and Arduino Mega. The wire is about 12 inches (1 Feet Approx) long. The one side of the wire has USB A type connector and the other corner has USB B type connector.
Taparia Multiple Bits Screwdriver BDS125
Taparia Multiple Bits Screwdriver BDS125 is a high quality multiple bits screwdriver. It has 10 multiple screw bits Torx T5, T6, T8, T10, Philips No. 0, 1, 2 and Flat 3mm, 4mm and 5mm. Its handle has a space where you can store all the bits.Â
LDR Light Sensor Module
LDR Light Sensor Module is utilized to identify the existence of light. LDR Light Sensor module goes high in the existence of light and it will become low in the absence of light. The sensitivity of the light sensing ( detection ) can be adjusted utilizing the in built potentiometer within the module.
Screw Terminals – 5.08mm Pitch 2 Pins
Screw Terminals – 5.08mm Pitch 2 Pins is a small pcb mounted terminal block. It can be soldered directly to the PCB and is used to connect wires tied by its screws. This terminal block includes screws to hold the wires in place. It can hold the wires from 12 to 22 AWG. The best thing about this connector is that you can interconnect these connectors to build multiple connectors such as 4 pins,6 pins,8 pins,10 pins,12 pins and so on.
Temperature Humidity Thermometer Clock HTC 1
Temperature Humidity Thermometer Clock HTC 1 is a Digital Monitoring Gadget that comes with Clock with Alarm, Digital Temperature Thermometer, Humidity Hygrometer displays on a significant large digits on LCD display. This gadget measures temperatures as low as -58 Fahrenheit ( -50 c ) and up to +158 Fahrenheit ( 70c ), and the clock has both 12 24 hour format, display temperature, humidity & time at the same time, memory of max-min humidity & temperature readings, a large digits LCD display, simple to read, low power usage.
DC Power Jack Female Connector PCB Mounted
DC Power Jack Female Connector PCB Mounted are ideal to use in distinct electronic projects where you require to connect disconnect the DC power supply to your circuit frequently. DC Power Jack Female Connector can be directly soldered to your Circuit PCB.
Male Headers Right Angle – 2.54mm Pitch – 40 Pins
Male Headers Right Angle – 2.54mm Pitch – 40 Pins is a 90 degree angle bent header use to mount directly on your pcb. It has a 2.54mm pitch that can be directly use in General PCB. It can also be connected with your arduino boards like Arduino UNO and Arduino Mega and Arduino Nano. Both corners of the pins are male pins that is bent at 90 degree angle. You can cut this header short as per your requirement.
Magnetic Sensor Switch – MC 38
Magnetic Sensor Switch – MC 38 is a Magnetic Switch can be used as a switch at door or window security system. It consist of two pieces one is a sensor wired and another is a magnetic bar enclosed in a plastic case.
Rain Drop Sensor Module
Rain Drop Sensor Module is used to detect rain. It senses the rain drops and alerts instantly. Rain Drop Sensor Module can be utilized to monitor a variety of climate conditions and grew to become into a number of fixed output signal and Analog output.
Popular Search
Arduino Boards, Sensors and Modules
View AllNEO 6M GPS Module
NEO 6M GPS Module is an extensive GPS module that is dependent on the NEO 6M. This device takes advantage of the most up-to-date technology to offer the excellent potential positioning information and consists of a larger integrated 25 x 25mm active GPS antenna with a UART TTL socket.
555 Motor
555 Motor is a high torque DC motor that can be used in various electronic projects, suitable for a variety of small electric drills applications, wood drilling, grinding and other small electric drill chuck accessories.
NODEMCU ESP8266 Wifi Development Board
NODEMCU ESP8266 Wifi Development Board is an IoT Module primarily based on ESP8266 wifi Module. NODEMCU ESP8266 Wifi Development Board employs Lua Scripting language and is an open source IoT (Internet of Things) platform has CH340g USB to TTL IC.
775 Motor
775 Motor is a high speed high torque DC motor that can be used in a variety of electronics projects, mini electric drills machines, grinding, CNC machines, RC Toys like Cars, RC Planes and much more.
Digital Voltmeter and Ammeter – 0 to 100V 10A
Digital Voltmeter and Ammeter – 0 to 100V 10A
Digital Voltmeter and Ammeter – 0 to 100V 10A is a Dual Led Voltage Current Measurement Module to indicate the voltage as well as current. The voltage displays in Red color and current displays in Blue color with an indicator V & A next to it.
DHT22 Temperature and Humidity Sensor Module
DHT22 Temperature and Humidity Sensor Module is one that includes the compound has been calibrated digital signal output of the temperature and humidity sensors. DHT22 Temperature and Humidity Sensor Module incorporates a capacitive sensor moist components and a high-precision temperature measurement devices and associated with a high-performance 8-bit microcontroller.
I2C IIC 128×64 OLED Display Module – 2.44 cm – 0.96 Inch
I2C IIC 128×64 OLED Display Module – 2.44 cm – 0.96 Inch
I2C IIC 128×64 OLED (Organic Light-Emitting Diode) Display Module – 2.44 cm – 0.96 Inch is a self light-emitting technology made up of a thin multi-layered natural and organic film positioned in between an anode and cathode. In contrast to LCD technological innovation, OLED does not need to have a backlight.
ULN2003 Stepper Motor Driver Module
ULN2003 Stepper Motor Driver Module uses the ULN2003 driver chip to amplify to regulate the signal from the Arduino. It is a low cost and light-weight device used to work and manage the little stepper motors.
Crocodile Clip Flexible Wires Multicolor – 5 Pcs
Crocodile Clip Flexible Wires Multicolor – 5 Pcs
Crocodile Clip Flexible Wires Multicolor – 5 Pcs are best to use in various electronic projects where you need to connect disconnect the circuit frequently. It is suitable to use to connect with Arduino Boards, Sensors and Modules. The wire is flexible about 19 inches long. Both sides of the wire has Crocodile/ Alligator type connectors covered with soft sleeve that work as an insulation.
Reed Switch Sensor Module
Reed Switch Sensor Module is a sensor that works as a on/off switch in the presence of a magnetic field. Reed Switch Sensors can be utilized in numerous applications exactly where contact less On/Off switching is required.
IR Sensor Module
IR Sensor module consists of superb adaptive capability of the ambient light, using a pair of infrared transmitter and the receiver tube, the infrared emitting tube emits a certain frequency, encounters an obstacle detection (reflecting surface)
LDR Light Sensor Module
LDR Light Sensor Module is utilized to identify the existence of light. LDR Light Sensor module goes high in the existence of light and it will become low in the absence of light. The sensitivity of the light sensing ( detection ) can be adjusted utilizing the in built potentiometer within the module.
Breadboard Flexible Jumper Wire – Female to Female – 40 Pcs
Breadboard Flexible Jumper Wire – Female to Female – 40 Pcs
Breadboard Flexible Jumper Wire – Female to Female – 40 Pcs are commonly in use with breadboard to connect Arduino Boards, Sensors and Modules. The wire is flexible about 8.5 inches long, its in belt shape and has multiple colors.
Breadboard Flexible Jumper Wire – Male to Male – 40 Pcs
Breadboard Flexible Jumper Wire – Male to Male – 40 Pcs
Breadboard Flexible Jumper Wire – Male to Male – 40 Pcs are commonly in use with breadboard to connect Arduino Boards, Sensors and Modules. The wire is flexible about 8.5 inches long, its in belt shape and has multiple colors.
UNO R3
UNO R3 Board has 32 Kb of Flash Memory and consists of 14 Digital Input / Output pins, 6 Analog Input pins, an Onboard 16 MHz Ceramic Resonator, Port for USB connection, Onboard DC Power Jack, An ICSP header and a micro-controller Reset button.
28BYJ 48 Stepper Motor
28BYJ 48 Stepper Motor is a high torque 4 Phase stepper motor operates with 5V and it has a speed of 2000 RPM. It incorporates adequate torque which is suitable to use in small robotic projects.
Finger Print Sensor Module – R307
Finger Print Sensor Module – R307 is an optical fingerprint sensor consists of high speed DSP processor, high performance fingerprint alignment algorithm, high capacity FLASH chips and other hardware & software framework, uncomplicated layout with fingerprint entry, fingerprint matching, stable functionality, image processing, search and template storage and other functions.
USB A To USB B Cable for Arduino – Blue Color
USB A To USB B Cable for Arduino – Blue Color
USB A To USB B Cable for Arduino – Blue Color is a High Quality USB Cable to use with Arduino Boards like Arduino UNO and Arduino Mega. The wire is about 12 inches (1 Feet Approx) long. The one side of the wire has USB A type connector and the other corner has USB B type connector.
MG90S Metal Gear Servo Motor
MG90S Metal Gear Servo Motor is a 360 degree rotation servo that processes PWM signal faster and better. It equips superior internal circuitry that offers good torque, retaining power, and faster updates in response to external forces.
Electronic Components
View All1uF 50V Electrolytic Capacitor Radial 105°C
TM1637 4 Digits 7 Segment LED Display Module
TM1637 4 Digits 7 Segment LED Display Module is an inexpensive solution for displaying the output data to your Arduino project. Even though the data displayed is limited by numbers still it enables end users to display some characters too like A, B, C etc.
GL12 Breadboard 840 Points
GL12 Breadboard 840 Points is a full size best quality breadboard for electronic circuits and arduino projects prototyping. The breadboard is known as for its 840 tie points. The backside of the breadboard contains the adhesive double sided tape for easy attachment with your projects chasis or body.
Electronic Parts
View AllUSB A To USB B Cable for Arduino – Blue Color
USB A To USB B Cable for Arduino – Blue Color
USB A To USB B Cable for Arduino – Blue Color is a High Quality USB Cable to use with Arduino Boards like Arduino UNO and Arduino Mega. The wire is about 12 inches (1 Feet Approx) long. The one side of the wire has USB A type connector and the other corner has USB B type connector.
220V AC Mains Wire Cable – 2 Pins
220V AC Mains Wire Cable – 2 Pins
220V AC Mains Wire Cable – 2 Pins is a High Quality Mains Cord/Wire. The wire is a 2.5 Yards (2.3 Meters Approx) long wire.
Male Headers Right Angle – 2.54mm Pitch – 40 Pins
Male Headers Right Angle – 2.54mm Pitch – 40 Pins is a 90 degree angle bent header use to mount directly on your pcb. It has a 2.54mm pitch that can be directly use in General PCB. It can also be connected with your arduino boards like Arduino UNO and Arduino Mega and Arduino Nano. Both corners of the pins are male pins that is bent at 90 degree angle. You can cut this header short as per your requirement.
DC Power Jack Female Connector Wired Black
DC Power Jack Female Connector Wired Black
DC Jack Female Connector Wired Black are best to use in various electronic projects where you need to connect disconnect the DC power supply to your circuit frequently. The wire is flexible about 6 inches long. One side of the wire has DC Female Jack connector covered with soft insulated material and the other corner has open wire that you can directly solder to the circuit you want to give power supply.
Mini DC Vibration Motor with Wire
Mini DC Vibration Motor with Wire
Mini DC Vibration Motor with Wire is a small yet highly powerful DC motor works on 1.5v to 5v DC voltage. It can be used with a variety of electronic creative projects such as toys, massagers, pagers, various devices, mobile phones etc.
Screw Terminals – 2.54mm Pitch 2 Pins
Screw Terminals – 2.54mm Pitch 2 Pins is a tiny and pcb mounted terminal block. It can be soldered directly to the PCB and is used to connect wires tied by screws. This terminal block includes screws to hold the wires in place. It can keep wires from 14 to 22 AWG. The best thing about this connector is that you can interconnect these connectors to build multiple connectors such as 4 pins,6 pins,8 pins,10 pins,12 pins and so on.
555 Motor
555 Motor is a high torque DC motor that can be used in various electronic projects, suitable for a variety of small electric drills applications, wood drilling, grinding and other small electric drill chuck accessories.
DC Power Jack Female Connector Wired
DC Power Jack Female Connector Wired
DC Power Jack Female Connector Wired are best to use in various electronic projects where you need to connect disconnect the DC power supply to your circuit frequently. The wire is flexible about 6 inches long. One side of the wire has DC Female Power Jack connector covered with soft insulated material and the other corner has open wire that you can directly solder to the circuit you want to give power supply.
N20 Micro Metal Gear Motor
N20 Micro Metal Gear Motor incorporates all metal gears, long lasting, small volume, significant torsion an ideal substitute for the rusty or damaged geared motors on the machine.
Mini DC Toy Motor
Mini DC Toy Motor is a small motor that can be used in various small toys and electronic projects. Mini DC Toy Motor works on an operating voltage of 3V to 6V. It can also be operated using 2 AA batteries or 5V USB power supply.
775 Motor
775 Motor is a high speed high torque DC motor that can be used in a variety of electronics projects, mini electric drills machines, grinding, CNC machines, RC Toys like Cars, RC Planes and much more.
Breadboard Flexible Jumper Wire – Female to Female – 40 Pcs
Breadboard Flexible Jumper Wire – Female to Female – 40 Pcs
Breadboard Flexible Jumper Wire – Female to Female – 40 Pcs are commonly in use with breadboard to connect Arduino Boards, Sensors and Modules. The wire is flexible about 8.5 inches long, its in belt shape and has multiple colors.
Male Headers – 2.54mm Pitch – 40 Pins
Male Headers – 2.54mm Pitch – 40 Pins is a header use to mount directly on your pcb. It has a 2.54mm pitch that can be directly use in General PCB. It can also be connected with your arduino boards like Arduino UNO and Arduino Mega and Arduino Nano. Both corners of the pins are male pins. You can cut it short as per your requirement.
MG90S Metal Gear Servo Motor
MG90S Metal Gear Servo Motor is a 360 degree rotation servo that processes PWM signal faster and better. It equips superior internal circuitry that offers good torque, retaining power, and faster updates in response to external forces.
Female Headers – 2.54mm Pitch – 40 Pins
Female Headers – 2.54mm Pitch – 40 Pins is a female header use to mount directly on your pcb. It has a 2.54mm pitch that can be directly use in General PCB. It can also be connected with your arduino boards like Arduino UNO and Arduino Mega and Arduino Nano. One side of the pins are male pins and the other side is female connector. You can cut this header short as per your requirement.
DC Power Jack Female Connector PCB Mounted
DC Power Jack Female Connector PCB Mounted are ideal to use in distinct electronic projects where you require to connect disconnect the DC power supply to your circuit frequently. DC Power Jack Female Connector can be directly soldered to your Circuit PCB.
28BYJ 48 Stepper Motor
28BYJ 48 Stepper Motor is a high torque 4 Phase stepper motor operates with 5V and it has a speed of 2000 RPM. It incorporates adequate torque which is suitable to use in small robotic projects.
Screw Terminals – 5.08mm Pitch 2 Pins
Screw Terminals – 5.08mm Pitch 2 Pins is a small pcb mounted terminal block. It can be soldered directly to the PCB and is used to connect wires tied by its screws. This terminal block includes screws to hold the wires in place. It can hold the wires from 12 to 22 AWG. The best thing about this connector is that you can interconnect these connectors to build multiple connectors such as 4 pins,6 pins,8 pins,10 pins,12 pins and so on.
Crocodile Clip Flexible Wires Multicolor – 5 Pcs
Crocodile Clip Flexible Wires Multicolor – 5 Pcs
Crocodile Clip Flexible Wires Multicolor – 5 Pcs are best to use in various electronic projects where you need to connect disconnect the circuit frequently. It is suitable to use to connect with Arduino Boards, Sensors and Modules. The wire is flexible about 19 inches long. Both sides of the wire has Crocodile/ Alligator type connectors covered with soft sleeve that work as an insulation.
Power Supplies
View AllCrocodile Clip Flexible Wires Multicolor – 5 Pcs
Crocodile Clip Flexible Wires Multicolor – 5 Pcs
Crocodile Clip Flexible Wires Multicolor – 5 Pcs are best to use in various electronic projects where you need to connect disconnect the circuit frequently. It is suitable to use to connect with Arduino Boards, Sensors and Modules. The wire is flexible about 19 inches long. Both sides of the wire has Crocodile/ Alligator type connectors covered with soft sleeve that work as an insulation.
Digital Voltmeter and Ammeter – 0 to 100V 10A
Digital Voltmeter and Ammeter – 0 to 100V 10A
Digital Voltmeter and Ammeter – 0 to 100V 10A is a Dual Led Voltage Current Measurement Module to indicate the voltage as well as current. The voltage displays in Red color and current displays in Blue color with an indicator V & A next to it.
TP4056 1A Lithium Battery Charging Module
TP4056 1A Lithium Battery Charging Module
TP4056 1A Lithium Battery Charging Module with Current Protection is an excellent battery charging module to charge a single 18650 lithium ion battery cell 3.7V 1 Ah or higher lithium-ion (Li-Ion) cells such as 16550s that don’t have their own individual protection circuit.
DC Power Jack Female Connector Wired
DC Power Jack Female Connector Wired
DC Power Jack Female Connector Wired are best to use in various electronic projects where you need to connect disconnect the DC power supply to your circuit frequently. The wire is flexible about 6 inches long. One side of the wire has DC Female Power Jack connector covered with soft insulated material and the other corner has open wire that you can directly solder to the circuit you want to give power supply.
DC Power Jack Female Connector Wired Black
DC Power Jack Female Connector Wired Black
DC Jack Female Connector Wired Black are best to use in various electronic projects where you need to connect disconnect the DC power supply to your circuit frequently. The wire is flexible about 6 inches long. One side of the wire has DC Female Jack connector covered with soft insulated material and the other corner has open wire that you can directly solder to the circuit you want to give power supply.
LM2596 DC-DC Buck Converter Module
LM2596 DC-DC Buck Converter Module
LM2596 DC-DC Buck Converter Module is an adjustable Step Down power supply. The Input DC Volt 3.2v – 40v converts into Output DC Volt 1.2v – 35v.
220V AC Mains Wire Cable – 2 Pins
220V AC Mains Wire Cable – 2 Pins
220V AC Mains Wire Cable – 2 Pins is a High Quality Mains Cord/Wire. The wire is a 2.5 Yards (2.3 Meters Approx) long wire.
MB102 Breadboard Power Supply Module 3.3V & 5V
MB102 Breadboard Power Supply Module 3.3V & 5V
MB102 Breadboard Power Supply Module that helps you to provide 3.3V & 5V power supply to your breadboard based project. MB102 Breadboard Power Supply Module is designed to directly plug into a Breadboard panel with 2 power Distribution strips. The module has ON / OFF switch to turn it ON and OFF.
DC Power Jack Male Connector Wired Black
DC Power Jack Male Connector Wired Black
DC Power Jack Male Connector Wired Black are best to use in various electronic projects where you need to connect disconnect the DC power supply to your circuit frequently. The wire is flexible about 8 inches long. One side of the wire has DC Power Male Jack connector covered with soft insulated material and the other corner has open wire that you can directly solder to your power supply.
Tools
View AllTaparia Multiple Bits Screwdriver BDS125
Taparia Multiple Bits Screwdriver BDS125 is a high quality multiple bits screwdriver. It has 10 multiple screw bits Torx T5, T6, T8, T10, Philips No. 0, 1, 2 and Flat 3mm, 4mm and 5mm. Its handle has a space where you can store all the bits.Â
Digital Voltmeter and Ammeter – 0 to 100V 10A
Digital Voltmeter and Ammeter – 0 to 100V 10A
Digital Voltmeter and Ammeter – 0 to 100V 10A is a Dual Led Voltage Current Measurement Module to indicate the voltage as well as current. The voltage displays in Red color and current displays in Blue color with an indicator V & A next to it.
Temperature Humidity Thermometer Clock HTC 1
Temperature Humidity Thermometer Clock HTC 1 is a Digital Monitoring Gadget that comes with Clock with Alarm, Digital Temperature Thermometer, Humidity Hygrometer displays on a significant large digits on LCD display. This gadget measures temperatures as low as -58 Fahrenheit ( -50 c ) and up to +158 Fahrenheit ( 70c ), and the clock has both 12 24 hour format, display temperature, humidity & time at the same time, memory of max-min humidity & temperature readings, a large digits LCD display, simple to read, low power usage.
9 in 1 Traveler Survival Multi Tool
9 in 1 Traveler Survival Multi Tool is a compact and versatile tool that is designed to be a useful companion for outdoor enthusiasts, travelers, and anyone who wants to be prepared for unexpected situations. This multi-tool includes a Plier, Nail File, Straight Screwdriver, Corkscrew, Large Flathead Screwdriver, Knife, Cross Screwdriver, Bottle Opener & Serrated Knife.
BULK REQUIREMENT?
Want to buy in bulk quantity, message us for the best price.